Posted by Dave'02LT on August 17, 04 at 19:57:48:
In Reply to: Re: Multiple Questions: posted by Jeff in CO on August 17, 04 at 15:52:20:
There is a TSB for sticking throttle on the Yukon. It involves plugging the hole in the throttle blade and adjusting the throttle blade angle. Best left to the dealer or a quality independant garage. See #1) below for the details.
Coolant level switch is in the reservoir and is the most likely suspect.
Rear Brakes - 2001 Silverado. There are a couple TSBs dealing with the rear parking brakes on the New Body Style(NBS) trucks. The fix is to replace the rear parking brake shoes (yes, similar to the Vettes) and spring retainer clip. The complete kit is avalable at dealer parts.
To Adjust:
In your case, back off the cable adjustment to where it was before, then adjust the star wheel on the brake shoes for a 'shoe to drum' clearance of 0.026in (requires rotor removal). Use a brake caliper tool to measure, or insure the clearance is close but without drag. Operate the emergency brake lever a couple of times and recheck.
#1)Increased Accelerator Pedal Effort, Idle Instability (Clean Throttle Body and Adjust Blade) TSB #02-06-04-054B - (03/17/2003)
This procedure only applies to cable actuated throttle bodies on the models listed above. This procedure should not be performed on electronically controlled throttle bodies or on any vehicle or engine that is not listed above in the Models section.
1. Verify that the cause for this condition is not a damaged or binding throttle cable.
2. Remove the air intake duct. Refer to Air Cleaner Duct Replacement.
3. Inspect the vehicle for installation of a fixed orifice PCV valve, refer to Corporate Bulletin Number 01-06-01-029B for PCV valve identification. Vehicles undergoing this throttle body procedure MUST use a Fixed Orifice PCV Valve, P/N 12572717.
4. Clean throttle body bore and throttle valve plate of carbon using a shop rag and an appropriate cleaner. Refer to Engine Controls Repair Procedures - Throttle Body Cleaning Procedure.
5. Select the correct plug for the size of the air bypass hole in the throttle body being serviced. Use a 1/8-inch (.125") drill bit to determine which plug to use.
* Vehicles built before introduction of the Fixed Orifice PCV Valve will have a 3.75 mm (.150") air bypass hole in the throttle plate. The 1/8-inch drill bit is smaller than the air bypass hole in these throttle bodies and can be inserted into the bypass hole. To plug the air bypass hole in these vehicles requires the yellow plug, P/N 12580749.
* Vehicles built after introduction of the Fixed Orifice PCV Valve will have a 2.6 mm (.104") air bypass hole in the throttle plate. The 1/8-inch drill bit is larger than the air bypass hole in these throttle bodies and cannot be inserted into the bypass hole. To plug the air bypass hole in these vehicles requires the red plug, P/N 12581011.
6. Insert the appropriate plug (1) into the air bypass hole in the throttle plate. Insert the "tail" end of the plug through the throttle plate air bypass hole.
7. Open the throttle plate to allow access to the tail end of the plug. Pull the tail section to securely position the plug into the air bypass hole and trim excess material (1) from plug.
8. Turn ignition key to the on position, with engine off.
9. Use the Tech 2 Scan tool to read initial TPS voltage.
Important
TPS voltage cannot exceed .69 V. If the vehicle has an initial TPS voltage greater than .61 V, replace the Throttle Body Assembly. This part is currently on parts restriction. Contact the General Motors Powertrain Quality Center at 866-654-7654 for assistance.
10. Using the Tech 2 Scan tool and a T15 driver to rotate the Minimum Air Rate screw, increase TPS voltage by .08 Volts (Refer to TPS Voltage Chart below).
11. Turn ignition key to the off position. Verify that the accelerator pedal moves freely - Depress the accelerator pedal to the floor and release.
12. Install the air intake duct. Refer to Air Cleaner Duct Replacement.
13. Start engine.
14. Using the Tech 2 scan tool, monitor TPS voltage and verify the TPS voltage is no greater than 0.69V.
15. Road Test Vehicle.